Super-micro-computer P4SCT Bedienungsanleitung

®SUPER P4SCTSUPER P4SCT+SUPER P4SCT+IIUSER’S MANUALRevision 1.0c SUPER

1-4SUPER P4SCT/P4SCT+/P4SCT+II User’s ManualFigure 1-4. SUPER P4SCT/P4SCT+/P4SCT+II Motherboard Layout CPU478 PGAMCHPWR LEDCOM2J17J21J20USB 1/2Par

C-24SUPER P4SCT/P4SCT+/P4SCT+II User's ManualNotes

Chapter 1: Introduction1-5P4SCT/P4SCT+/P4SCT+II Quick ReferenceJumpers Description Default SettingJ18 Speaker Pins 3-4 (In.Buzzer)J33 VGA Enable/Disab

1-6SUPER P4SCT/P4SCT+/P4SCT+II User’s ManualFigure 1-6.P4SCT/P4SCT+/P4SCT+II System Block Diagram: (with the 6300ESBHance Rapids Chipset)Note: This is

Chapter 1: Introduction1-7Motherboard FeaturesCPU  Latest CPU technology!• Single Pentium® 4 478-pin PGA processors or Intel Celeron processorsup to

1-8SUPER P4SCT/P4SCT+/P4SCT+II User’s ManualACPI Features• Microsoft OnNow• Slow blinking LED for suspend state indicator• BIOS support for USB keyboa

Chapter 1: Introduction1-91-2 Chipset Overview: Intel's Canterwood(875P) andCanterwood ES (E7210)Intel’s Canterwood Chipset (875P) and Canterwood

1-10SUPER P4SCT/P4SCT+/P4SCT+II User’s ManualMarvell's 88SX5041 Host Controller(*For the P4SCT+/P4SCT+II only) The Marvell 88SX5080 device is a P

Chapter 1: Introduction1-111-3 PC Health MonitoringThis section describes the PC health monitoring features of the SUPERP4SCT/P4SCT+/P4SCT+II. The mo

1-12SUPER P4SCT/P4SCT+/P4SCT+II User’s Manual1-4 Power Configuration SettingsThis section describes features of your motherboard that deal with powera

Chapter 1: Introduction1-13Wake-On-LAN is defined as the ability of a management application toremotely power up a computer that is powered off. Remo

The information in this User’s Manual has been carefully reviewed and is believed to beaccurate. The vendor assumes no responsibility for any inaccur

1-14SUPER P4SCT/P4SCT+/P4SCT+II User’s Manual1-6 Super I/OThe disk drive adapter functions of the Super I/O chip include a floppy diskdrive controller

Chapter 2: Installation2-1Chapter 2Installation2-1 Static-Sensitive DevicesElectric Static Discharge (ESD) can damage electronic components. Topreven

2-2SUPER P4SCT/P4SCT+/P4SCT+II User's ManualIMPORTANT: Always connect the power cord last and always remove itbefore adding, removing or changin

Chapter 2: Installation2-35. Lift the lever on the CPU socket.Socket Lever6. Install the CPU in the socket. Make sure thatPin 1 of the CPU is seated

2-4SUPER P4SCT/P4SCT+/P4SCT+II User's Manual2-4 Installing DDR MemoryCAUTIONExercise extreme care when installing or removing memorymodules to pr

Chapter 2: Installation2-5To Install:Insert modulevertically andpress downuntil it snapsinto place.Pay attentionto the notch.Figure 2-2. Side and Top

2-6SUPER P4SCT/P4SCT+/P4SCT+II User's ManualFigure 2-4. Front Control Panel Connectors2-5 I/O Port/Control Panel Connector LocationsThe I/O port

Chapter 2: Installation2-72-6 Connecting CablesPower Supply ConnectorsThe primary power supplyconnector (J20) on the P4SCT/P4SCT+/P4SCT+II meets the S

2-8SUPER P4SCT/P4SCT+/P4SCT+II User's ManualReset ConnectorThe reset connector is located onpins 3 and 4 of JF1. This connec-tor attaches to the

Chapter 2: Installation2-9LAN1 LEDPower ButtonOverheat LED1Reset Button2IDE LEDPower On LEDResetPwrVccVccVccVccGroundGround1920VccXGroundNMIXXXLAN2 LE

PrefaceAbout This ManualThis manual is written for system integrators, PC technicians andknowledgeable PC users. It provides information for the inst

2-10SUPER P4SCT/P4SCT+/P4SCT+II User's ManualLAN1 LEDPower ButtonOverheat LED1Reset Button2IDE LEDPower On LEDResetPwrVccVccVccVccGroundGround192

Chapter 2: Installation2-11LAN1 LEDPower ButtonOverheat LED1Reset Button2IDE LEDPower On LEDResetPwrVccVccVccVccGroundGround1920VccXGroundNMIXXXLAN2 L

2-12SUPER P4SCT/P4SCT+/P4SCT+II User's ManualFan HeadersThere are six fan headers on theP4SCT/P4SCT+/P4SCT+II, whichare designated CPU/Chassis Fa

Chapter 2: Installation2-13Chassis IntrusionThe Chassis Intrusion header isdesignated JL1. See the boardlayout in Chapter 1 for the locationof JL1 an

2-14SUPER P4SCT/P4SCT+/P4SCT+II User's ManualEthernet Ports GLAN1 andGLAN2 (*P4SCT/P4SCT+IIonly)Two Ethernet ports(designated GLAN1 andGLAN2) are

Chapter 2: Installation2-15Universal Serial Bus (USB)There are two Universal SerialBus Connectors (USB 1/2: J12/J13) located on the I/O panel andaddi

2-16SUPER P4SCT/P4SCT+/P4SCT+II User's ManualPinNumber12DefinitionGroundWake-upWake-On-Ring PinDefinitions (WOR)Keylock Enable/DisableThe Keylock

Chapter 2: Installation2-17Intel's SATA LEDThe header for Intel's SATA LEDis located on J37. This header willdisplay all Intel's SATA

2-18SUPER P4SCT/P4SCT+/P4SCT+II User's ManualCMOS ClearJBT1 is not actually a jumper butconsists of two contact pads. Toclear the contents of CM

Chapter 2: Installation2-19USB Wake-Up (*USB1/2Only)Use JPUSB1 to enable or disableUSB Wake-Up, which allows youto wakeup the system by de-pressing a

SUPER P4SCT/P4SCT+/P4SCT+II User’s ManualivTable of ContentsAbout This Manual ...

2-20SUPER P4SCT/P4SCT+/P4SCT+II User's ManualWatch Dog Enable/DisableJP8 enables the Watch Dog func-tion. Watch Dog is a system moni-tor that ca

Chapter 2: Installation2-21GLAN2 Enable/Disable(*P4SCT+/P4SCT+ only)Change the setting of jumper JPL2to enable or disable the onboardLAN on the mothe

2-22SUPER P4SCT/P4SCT+/P4SCT+II User's ManualFront Side Bus SpeedJP1, JP2 are used to set the sys-tem (front side) bus speed for theprocessors.

Chapter 2: Installation2-232-8 Parallel Port, Floppy Drive, Hard Drive and AGPConnectionsUse the following information to connect the floppy and hard

2-24SUPER P4SCT/P4SCT+/P4SCT+II User's ManualIDE ConnectorsYou do not need to configurethe onboard IDE interfaces (-Pins 13,14 of JF1.) Refer to

Chapter 2: Installation2-251.5V 8xAGP Pro Slot (*P4SCT/P4ST+II)The P4SCT/P4SCT+/P4SCT+II includes an 8xAGP Pro slot for high-performance video cards.

2-26SUPER P4SCT/P4SCT+/P4SCT+II User's ManualNotes

3-1Chapter 3: TroubleshootingChapter 3Troubleshooting3-1 Troubleshooting ProceduresUse the following procedures to troubleshoot your system. If you h

3-2SUPER P4SCT/P4SCT+/P4SCT+II User's ManualNOTE: If you are a system integrator, VAR or OEM, a POSTdiagnostics card is recommended. For I/O por

3-3Chapter 3: Troubleshooting2. BIOS upgrades can be downloaded from our web site athttp://www.supermicro.com/techsupport/download.htm.Note: Not all

ATX PS/2 Keyboard/Mouse Ports ... 2-15Universal Serial Bus (USB)...

3-4SUPER P4SCT/P4SCT+/P4SCT+II User's ManualQuestion: What's on the CD that came with my motherboard?Answer: The supplied compact disc has

3-5Chapter 3: TroubleshootingQuestion: How do I connect the ATA100/66 cable to my IDEdevice(s)?Answer: The 80-wire/40-pin high-density ATA100/66 IDE

3-6SUPER P4SCT/P4SCT+/P4SCT+II User's ManualNotes

Chapter 4: BIOS4-1Chapter 4BIOS4-1 IntroductionThis chapter describes the AwardBIOS for the P4SCT/P4SCT+/P4SCT+II.The Award ROM BIOS is stored in a Fl

SUPER P4SCT/P4SCT+/P4SCT+II User's Manual4-24-2 Running Setup*Optimal default settings are in bold text unless otherwise noted.The BIOS setup op

Chapter 4: BIOS4-3 IDE Channel 0 Master/Slave, IDE Channel 1 Master/Slave, IDEChannel 2 Master, IDE Channel 3 MasterPress the <Auto> key to ac

SUPER P4SCT/P4SCT+/P4SCT+II User's Manual4-44-4.1 Advanced BIOS FeaturesWhen the item of Advanced BIOS Features is highlighted, press the<E

Chapter 4: BIOS4-5ACPI FunctionSelect "Enabled" to activate the function of BIOS Support for AdvancedConfiguration and Power Interface feat

SUPER P4SCT/P4SCT+/P4SCT+II User's Manual4-6ECC ConfigurationThis setting allows you to enable or disable ECC (Error Correction andChecking). T

Chapter 4: BIOS4-7USB Legacy SupportThis setting allows you to enable or disable the functions of USB, Keyboard/Mouse under POST and DOS. The options

viTable of ContentsChapter 4: BIOS4-1 Introduction...

SUPER P4SCT/P4SCT+/P4SCT+II User's Manual4-8UART Mode SelectThis setting allows the user to select the UART mode for the BIOS. Theoptions are &

Chapter 4: BIOS4-94-4.4 PnP ConfigurationChoose PCI/PnP Configurations from the Award BIOS main menu with theLeft/Right arrow keys. You should see t

SUPER P4SCT/P4SCT+/P4SCT+II User's Manual4-10Resources Controlled ByThis setting allows BIOS to automatically configure all boot and Plug andPla

Chapter 4: BIOS4-114-4.6 Hardware MonitorChoose Hardware Monitor from the Award BIOS main menu with the Left/Right arrow keys. You should see the fol

SUPER P4SCT/P4SCT+/P4SCT+II User's Manual4-12Hyper-Threading TechnologySelect "Enabled" to activate the hyper-threading function of th

Chapter 4: BIOS4-13Set Supervisor PasswordWhen the item "Set Supervisor Password" is highlighted on the abovescreen, press the <Enter>

SUPER P4SCT/P4SCT+/P4SCT+II User's Manual4-14First Boot DeviceThis item allows the user to set the first boot-up device. The options are"R

Chapter 4: BIOS4-154-7 ExitChoose Exit from the Award BIOS main menu with the Left/Right arrowkeys. You should see the following display:Save & E

SUPER P4SCT/P4SCT+/P4SCT+II User's Manual4-16Load Fail-Safe DefaultsHighlight this item and hit <Enter> to load the default settings for a

A-1Appendix A: BIOS POST MessagesAppendix ABIOS POST MessagesDuring the Power-On Self-Test (POST), the BIOS will check for problems. If a problemis

Chapter 1: Introduction1-1Chapter 1Introduction1-1 OverviewChecklistCongratulations on purchasing your computer motherboard from an ac-knowledged lead

A-2SUPER P4SCT/P4SCT+//P4SCT+II User's ManualNotes

Appendix B: Award BIOS POST CodesB-1Appendix B: Award BIOS POST CodesThis section lists the POST (Power On Self Testing) Codes for the Award BIOS.POS

SUPER P4SCT/P4SCT+//P4SCT+II User’s ManualB-2 POST (hex) Description 0Fh Reserved 10h Auto detect flash type to load appropri

Appendix B: Award BIOS POST CodesB-3 2Dh 1. Initialize multi-language 2. Put information on screen display, including Award title, CPU type, CPU sp

SUPER P4SCT/P4SCT+//P4SCT+II User’s ManualB-4 POST (hex) Description 58h Reserved 59h Initialize the combined Trend Anti-Viru

Appendix B: Award BIOS POST CodesB-5 POST (hex) Description 80h Reserved 81h Reserved 82h 1. Call chipset power management hoo

SUPER P4SCT/P4SCT+//P4SCT+II User’s ManualB-6NOTES

Appendix C: Software Installation InstructionsC-1 Appendix CInstalling Software Drivers and WindowsOperating SystemAfter all the hardware has been in

C-2SUPER P4SCT/P4SCT+/P4SCT+II User's Manual ATA Operate ModeYou can select from the following two modes: Combined Mode and En-hanced Mode.Combin

Appendix C: Software Installation InstructionsC-3Configuring BIOS settings for the SATA RAID Functions(Enhanced Mode)1. Press the <Del> key dur

1-2SUPER P4SCT/P4SCT+/P4SCT+II User’s ManualContacting SupermicroHeadquartersAddress: SuperMicro Computer, Inc.980 Rock Ave.San Jose, CA 95131 U.S.A.

C-4SUPER P4SCT/P4SCT+/P4SCT+II User's ManualThe Adaptec Embedded Serial ATA with HostRAID Con-troller DriverAdaptec's Embedded Serial ATA RA

Appendix C: Software Installation InstructionsC-5Managing ArraysSelect this option to view array properties, and delete arrays. Thefollowing sections

C-6SUPER P4SCT/P4SCT+/P4SCT+II User's ManualViewing Array PropertiesTo view the properties of an existing array:1. At the BIOS prompt, press Ctrl

Appendix C: Software Installation InstructionsC-7Creating ArraysBefore creating arrays, make sure the disks for the array areconnected and installed i

C-8SUPER P4SCT/P4SCT+/P4SCT+II User's ManualAssigning Array PropertiesOnce you've create a new array, you are ready to assign the properties

Appendix C: Software Installation InstructionsC-92. Under the item "Arrays Label", type in an label and press Enter.(*Note: The label shal

C-10SUPER P4SCT/P4SCT+/P4SCT+II User's ManualNotes:1. Before adding a new drive to an array, back up any data contained onthe new drive. Otherwis

Appendix C: Software Installation InstructionsC-11Adding a Bootable ArrayTo make an array bootable:1. From the Main menu, select Manage Arrays.2. From

C-12SUPER P4SCT/P4SCT+/P4SCT+II User's ManualAdding/Deleting Hotspares(*Note: In order to rebuild a RAID (RAID 0 or RAID 1), you would need toa

Appendix C: Software Installation InstructionsC-13Initializing Disk DrivesIf an installed disk does not appear in the disk selection list forcreating

Chapter 1: Introduction1-3Figure 1-1. SUPER P4SCT ImageSUPER P4SCT(1. *Please see Notes on the next page for the differences between theP4SCT, the P

C-14SUPER P4SCT/P4SCT+/P4SCT+II User's Manual4. Use the up and down arrow keys to highlight the disk you wishto initialize and press Insert (as

Appendix C: Software Installation InstructionsC-155. Repeat Step 4 so that both drives to be initialized are selected (asshown in the screen below).6.

C-16SUPER P4SCT/P4SCT+/P4SCT+II User's ManualRebuilding Arrays*Note 1: Rebuilding applies to Fault Tolerant array (RAID 1) only.If an array Build

Appendix C: Software Installation InstructionsC-17Using the Disk UtilitiesThe Disk Utilities enable you to format or verify the media of your SerialAT

C-18SUPER P4SCT/P4SCT+/P4SCT+II User's Manual3 Select the desired disk and press Enter (as shown in the screenbelow.)2. From the ARC menu, selec

Appendix C: Software Installation InstructionsC-19You can choose from the following options:1. Format Disk—Simulates a low-level format of the hard d

C-20SUPER P4SCT/P4SCT+/P4SCT+II User's Manualm. After Windows OS Installation is completed, the system will automati-cally reboot.C-2 Installing

Appendix C: Software Installation InstructionsC-21Driver/Tool Installation Display Screen(*Note: Click the icons showing a hand writing on paper to vi

C-22SUPER P4SCT/P4SCT+/P4SCT+II User's ManualSupero Doctor IIIThe Supero Doctor III program is a Web base management tool thatsupports remote man

Appendix C: Software Installation InstructionsC-23Supero Doctor III Interface Display Screen-II (Remote Control)(*Note: SD III Software Revision 1.0